Showing 1–16 of 105 results

  • relay module

    Kidde CO120X – Carbon Monoxide Relay Module – Ac

    $33.59

    In stock

    • Can be used to activate auxiliary warning devices such as external bells and sirens, hallway or stairway lighting
    • The relay will only activate when it receives a CO signal from an interconnect Carbon Monoxide Alarm
    • When in the activated mode (as a result of a CO signal), this device will deactivate if it receives a smoke interconnect signal from a compatible device
    Add to cartLoading Done
  • 10 amp relay module

    Fire-Lite PAM-1 10 Amp Relay Module

    $39.26

    Only 1 left in stock

    Air Products & Controls, Inc. PAM-1, PAM-2, and PAM-4 MultiVoltage Relay Modules are encapsulated multi-voltage devices. The PAM-1 relay provides 10.0 Amp Form-C contacts and may be energized by one of three input voltages: 24 VAC, 24 VDC, or 115 VAC.

    Add to cartLoading Done
  • encapsulated relay

    Space Age SSU-PAM-2, Multi-Voltage Series Relay, 7A, SPDT, E

    $28.63

    Only 9 left in stock

    • The SSU-PAM-2 Relay provides 7.0 A form “C” contacts.
    • The relay may be energized by one of two input voltages: 12VDC or 24VDC.
    • The input voltages are polarity-sensitive and diode-protected.
    Add to cartLoading Done
  • encapsulated relay

    Spaceage 10AMP SPDT POLARIZED RELAY – O6-PAM4

    $28.63

    Only 16 left in stock

    • Flying Leads
    • 10 amp form c contacts
    • Polarity Sensitive / diode protected
    Add to cartLoading Done
  • conventional relay

    Space Age Ssu-Pam-Sd, Multi-Voltage Series Relay, 7A, Spdt,

    $22.91

    In stock

    • Flying Leads
    • 7 amp form C contacts
    • Polarity Sensitive / diode protected
    Add to cartLoading Done
  • Altronix AL800LGK9E Logic Board Replacement for AL602, AL802

    $129.48

    Only 16 left in stock

    The AL800LGK9E Logic Board is a replacement board for use in the AL602/AL802/AL1002ULADA Power Extender enclosures. Main Features two (2) Class A or two (2) Class B FACP inputs two (2) NC dry contact trigger inputs two (2) Class A or four (4) Class B notification circuits of which two (2) Class B outputs may…

    Add to cartLoading Done
  • Nac Power Extender 10A 4Out Sync 864, 9Th

    $610.92

    Only 16 left in stock

    • 2-wire horn/strobe Sync mode allows audible notification appliances (horns) and visual notification appliances (strobes) to be silenced/deactivated at the same time.
    • Signal circuit trouble memory (helps identify intermittent loop problems).
    • Ground fault detection.
    Add to cartLoading Done
  • Altronix NAC Power Extender – 24VDC @ 8 AMP. 4 –

    $510.67

    Only 15 left in stock

    • 2-wire horn/strobe Sync mode allows audible notification appliances (horns) and visual notification appliances (strobes) to be silenced/deactivated at the same time.
    • Signal circuit trouble memory (helps identify intermittent loop problems).
    • Ground fault detection.
    Add to cartLoading Done
  • Module (24v, 2 pair, hybrid field repl suppression module wi

    $87.15

    In stock

    • Protect two 24V pairs per module
    • Multi-stage SAD technology provides the best possible protection
    • Field-replaceable modules with hard-wired multi-base mounting system allows you to protect up to ten pairs with a common ground
    Add to cartLoading Done
  • Ditek 54kA Series Connected Surge Protector with Dry Contact

    $192.95

    In stock

    • Protects 120VAC power with dry contacts for remote monitoring of surge protection status
    • Series design for fast response and best protection
    • Installed in a NEMA 4X enclosure
    Add to cartLoading Done
  • Power Booster, 10 Amp, Red

    $551.24

    In stock

    Power Booster, 10 Amp, Red EBPS10A The Remote Booster Power Supply is a self-contained 24V DC power supply designed to augment fire alarm audible and visual power requirements. The booster contains all of the necessary circuits to monitor and charge batteries, control and supervise four Class B or two Class A Notification Appliance Circuits (NACs)…

    Add to cartLoading Done
  • Sale!

    Edwards-Signaling Power Booster, 6.5 Amp, Red, EBPS6A

    Original price was: $485.96.Current price is: $436.00.

    In stock

    Edwards-Signaling Power Booster, 6.5 Amp, Red, EBPS6A The Remote Booster Power Supply is a self-contained 24V DC power supply designed to augment fire alarm audible and visual power requirements. The booster contains all of the necessary circuits to monitor and charge batteries, control and supervise four Class B or two Class A Notification Appliance Circuits…

    Add to cartLoading Done
  • System Sensor EOLR-1 End-of-Line Epoxy Encapsulated (SPST) R

    $38.59

    Only 13 left in stock

    • Potted with pigtail
    •  Epoxy encapsulated
    • Single-pole single-throw
    Add to cartLoading Done
  • Fire-Lite ANN-RLY Relay Module with 10 Programmable Form Rel

    $326.65

    In stock

    • ANN-RLY connects to the ANN-BUS terminal on the FACP and requires minimal programming.
    • Provides 10 programmable Form-C relays.
    • Ten Form-C relays can be programmed for various functions; Alarm, Trouble, Supervisory, AC Loss, Waterflow Delay, Input Zones and Silenceable Alarm.
    Add to cartLoading Done
  • Fire-Lite FCPS-24S8RB Master Control Replacement Board

    $733.58

    In stock

    Master Control Replacement Board For The  FL-FCPS24FS8 The Fire•Lite FCPS-24FS8(C/E) is a compact, cost-effective, 8-amp remote power supplies with battery charger. The FCPS24FS8C/E) may be connected to any 12 or 24 volt fire alarm control panel (FACP) or may stand-alone. Primary applications include notification appliance (bell) circuit (NAC) expansion (to support ADA requirements and NAC…

    Add to cartLoading Done
  • Fire-Lite PWRMOD24 NAC Power Expander

    $182.15

    In stock

    The PWRMOD24 is an optional module that provides an additional 3 amps of NAC power.

    Add to cartLoading Done

A fire alarm relay allows your fire alarm system to perform automated tasks incase of an emergency. The relay distributes power to devices in certain circumstances. They can be used to close fire doors, switch off music systems, switch off air conditioning and more.

Fire alarm control panels require reliable power sources to operate in an emergency. This can be done through having two different power sources such as a primary power source and an emergency generator. Another option is a single power supply source such as primary ac power and a stored energy emergency power supply system

The power supply must be able to run the system for 24 hours in standby and 5 minutes in alarm conditions.